I used 24 centimeters as my push point as it resulted in enough force for my gauge to respond well, around halfway in the test instrument range of 0-200 Newtons. On our favorite chart, a “twist” force of 20/23/26 Nm is DIN 2.5 with a ~24 centimeter boot sole. (And remember the heel fittings are identical in performance, so no change in vertical release.)Īlso regarding the spreadsheet, please know that the “DIN” number is an approximation, as DIN is based on boot sole length and our 24 centimeter faux sole length is down on the lowest end of the DIN charts. Again, our numbers indicate that while doing precision setting of release values you’ll want to increase your lateral release settings for Sportiva-Trab fittings at most 1/2 a DIN number. Remember this is only for the toe, nearly all retention and release tension with a classic tech binding is provided by the heel. Don’t be alarmed by the percentage differences. Indeed, while the percentage difference in release force is minimal when you’re in downhill mode, it’s more significant in touring mode where going unlocked with an ION might give you enough retention with a fully Dynafit clone toe fitting, but enough less retention with Spectre to result in you bending at the waist and locking them up, for the up. I did measure the toe pin insertion depth of the ION, Sportiva came in at 92.03 mm wing width, with Dynafit new boot at 91.9, so they’re virtually identical at four tenths of a millimeter difference, which we assume is within manufacturing tolerances.Īlso be aware that this slight reduction in retention force at the toe will influence how easily you can backcountry tour with your binding toes unlocked (something we enjoy doing with ION, for example). In our opinion, what makes the Trab offer slightly less toe retention is the tiny amount of additional ramp on the fitting, as shown above. Lack of the Dynafit “Quick Step In” lead notch is not a deal breaker for ski touring, though the Quick Step is a nice feature for noobs. Trab managed to make their fittings nearly identical to Dynafit’s in terms of release and retention performance. Or better, as always, throw your skis on a test machine and see what your settings are actually yielding (reminder number 462 : “DIN” numbers printed on ski bindings are just an approximation, for roughly setting release values “RV” before testing.) But if you do precision DIN settings, be aware you’ll want to bump up your lateral tension a hair. For those of you who tend to dial up your settings, unnoticeable. According to our testing they do yield slightly less release resistance, on the order of a half a DIN number or so. Smooth lateral release, no sticking or catching. Where the Trabuchian smarts come in is the Trab toe fittings test out beautifully. It’s the toe where potential weirdness resides like an imaginary alien gray hovering over your sleeping form, contemplating an abduction for experimental shenanigans. Firstly, don’t fret whatsoever on the heel fittings. If Albert Einstein was a freeride tour skier, he’d call the “TechTrab” fittings genius. (Note, Trab has truly interesting bindings, check them out.) Folks are questioning the performance of La Sportiva’s “hybrid” “tech-Trab” fittings (used in their Spectra 2.0 boot and others), designed to function with both “standard” tech bindings as well as Trab’s Attaco TR2. As with any gossip, do not trust - verify like crazy before you base your credit card I/O or personal safety on what you hear muttered over the digi-waves. The ski touring rumor factory : You could banshee scream “IT’s ALIVE” and you wouldn’t be far off the mark. BEAR IN MIND, this test was performed WITHOUT THE HEEL LATCHED to measure retention tension of the toe unit presumably related to the shape of the boot toe tech fittings. Much of the variation in my data sets is no doubt due to using poorly regulated muscle power to push the gauge, but my results had obvious consistencies so I didn’t trouble with creating a mechanical force injector. The heel of the boot is held by an anti-friction shim at the same level as if latched in downhill mode. As engineer Cam Shute of G3 says, “Don’t talk about it unless you can measure it.” I used this unit as a “push” gauge, with only my muscle power and a slide platform made from plexiglass to reduce friction. And yes that’s a real “force gauge” measurement instrument. So, boys and girls, we lashed up this rig using the G3 ION as it provides consistent release, and noticeably more clamping pressure than most other bindings, which makes them work well as a test bed.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |